ATV Spec:
DP.V56RL.813 is an integration board of power supply, LED driver and TV board. 该款是电源、恒流驱动、TV 一体的电视板。
DP.V56RL.813 is an analog TV control board, which is suitable for Asia-pacific and middle-east market. 该款是模拟电视控制主板，适用于亚太及中东市场。
DP.V56RL.813’s USB slot can be used for updating software and playing multimedia,
such as MP3 and JPEG.
该款方案的USB 接口可用于软件升级和多媒体播放。
DP.V56RL.813’s power part is an energy-efficient ultrathin DC-line switching power supply unit, with max 75W/115VAC input,65 watts multi-output. It fits to 32〞to 46〞LED backlight TFT panel. 该款方案的电源部分是高效率开关电源，功率最大输入为75W/115VAC，总输出功率为65W，支持32到46寸 LED背光的TFT屏。
DP.V56RL.813’s Supports the bluetooth enabled active connected device to play music 支持带蓝牙功能的主动式连接的设备播放音乐
For safety issue, please keep the board 8.0mm away from metal parts of the TV at least. 基于安全考虑，请在安装时确保板卡与其他金属材料保持 8.0mm 以上的距离。
 Protect the board from static electrostatic in care of damage to the IC. 请使板卡远离静电以免损坏 IC。
 Keep the board away from conductor when it is working. 确保板卡工作时远离导体。
 Don’t press, distort or disassemble the board. 请勿强压、扭曲或拆解板卡。
 Clean the board with soft dry cloth when it’s dirty. 若板卡有污渍，请用干布擦拭。
 Don’t switch on the power supply before panel is correctly connected. 正确连接好屏线前请勿通电。
 Relative humidity:≤80% 相对湿度:≤80%.
 Storage temperature: -10~60°C 储存温度:-10~60°C
 Operation temperature: 0~40°C 工作温度:0~40°C
 The brightness of panel is influenced greatly by temperature, you should measure it after power on 10~30 minutes. 因屏的亮度易受温度影响，请在开机 10~30 分钟后再测量。
 Keep the board surface clean. Check the appearance of the board if there has any defective parts, such as dilapidate, weighty nick, etc.
保持产品表面整洁。检查产品外观是否有明显品质不良存在，如:破损，严重划痕等。

Note:1、Standard configurations above could match any following backlight Spec.
2、Specific backlight current can be selected in the following list according to customer's requirement, and different current can be achieved by changing the software.交流市电输入(2PIN-7.92mm);电源输出12V 和24V，恒流:38V-70V/25W AC input(2PIN-7.92mm);Power Output: 12V and 24V,backlight
voltage and power value: 38V-70V/25W交流市电输入(2PIN-7.92mm);电源输出12V 和24V，恒流:40V-70V/35W AC input(2PIN-7.92mm);Power Output: 12V and 24V,backlight
voltage and power value: 40V-70V/35W交流市电输入(2PIN-7.92mm);电源输出12V 和24V，恒流:40V-70V /45W AC input(2PIN-7.92mm);Power Output: 12V and 32V,backlight
voltage and power value: 40V-70V /45W交流市电输入(2PIN-7.92mm);电源输出12V 和32V，恒流:60V-90V /45W AC input(2PIN-7.92mm);Power Output: 12V and 24V,backlight
voltage and power value: 60V-90V /45W交流市电输入(2PIN-7.92mm);电源输出12V和24V，恒流:20V-58V /25W AC input(2PIN-7.92mm);Power Output: 12V and 32V,backlight
voltage and power value: 20V-58V /25W
8.4 Fuse Protection (保险丝保护)
The fuse inside the power supply will disconnect when the AC input current is over the rated current of fuse. Power off to protect the power module.
当输入交流电流超过保险丝的额定工作电流时，电源保险丝将断开，关闭电源供应以保护电 源模块。
8.5 Reset After Shutdown(保护功能复位)
The integration board will restart after the fault clearance.
  故障消除后，集成板即可恢复。
9.International Standards(国际标准)
9.1 EMC (电磁兼容性)
9.1.1 EMI standards (EMI 标准)
The power supply shall compliance with the following radio disturbance Criterion
  该电源应符合下列无线电干扰标准
 Sound and television broadcast receivers and associated equipment 声音和电视广播接收机及有关设备The power supply shall compliance with the following immunity Criterion
  该电源应符合下列抗扰度标准
 Sound and television broadcast receivers and associated equipment 声音和电视广播接收机及有关设备The power supply shall compliance with the following safety Criterion
电源应符合以下安全标准
 Sound and television broadcast receivers and associated equipment 声音和电视广播接收机及有关设备100% Hi-pot tested, Primary to second: 3KVAC or 4242VDC 3 second
初级到次级，100%耐高压测试，条件是3000V交流或4242V直流输入，持续时间3秒